Vehicles
223 not categorized PORSCHE 930 BACK ORDERCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.93050319700 This seal sits on the trailing edge of the front fender at the top just below the windshield. It is also used under the back of the rear quarter panel where it meets the side panel. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 4 necessary per car. Driver's or passengers side fitment (lhd). View/Change Diagram
From $4.92
Make a selection 93060290401 Distributor caps are often overlooked as the source of ignition issues. If yours is failing or cracked, you can experience shaking at idle, poor starting in the cold, stalling and backfiring. Be sure to replace it if you see any signs of cracking. High-quality Bosch replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. View/Change Diagram
From $21.28
Make a selection 93060290401A Distributor caps are often overlooked as the source of ignition issues. If yours is failing or cracked, you can experience shaking at idle, poor starting in the cold, stalling and backfiring. Be sure to replace it if you see any signs of cracking. This is a high-quality beru replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $26.40
Make a selection 96410628308 This cover sits upright along the back of the motor nearest the fire wall on the left side. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend replacing the grommet, part 91160640700 at the same time. Sold individually. 1 necessary per car. Please note: small modifications may be necessary between models View/Change Diagram
From $413.60
Make a selection 21011199312 Improve sound and performance by decreasing exhaust backpressure with our sport catalytic kits. This kit utilizes high quality, 100 cell German tri-metallic cats and includes all the necessary gaskets and hardware for installation. Please note: an ecu upgrade will be necessary. Please ensure what type of flanges you have prior to ordering. General Fitment911 1994-98
From $2,677.39
Make a selection BES99729000S2 M&m street-sport pdk muffler for 2009- 997.2 / 997.2s General Fitment911 2005-08
$3,529.90
Make a selection 96434703200 If your outer tie rods are worn you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be very dangerous and can seriously affect steering control. Prevent that from happening by replacing them as quickly as possible with our genuine replacement inner tie rods. Once you do, you will experience tighter, more precise feedback without noise. Complete kit consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Ball joint end 1 qty. Lock nut & pin sold individually. Left or right side fitment. 2 qty. Required. Tech tip: replace the inner tie rods also for a new car steering feel ! Purchase our part # 96434705804 & 96434719...(choose a part on the right to read more) View/Change Diagram
From $55.29
Make a selection 964604104X This part is a remanufactured part, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle actually starting. Eventually you hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter be sure to check the rubber cap on the terminal for cracks which allows moisture in ...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $250.59
Make a selection 99334703181 If your tie rod is worn, you will experience sloppy steering response and knocking / creaking sounds. Your tie rod keeps the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut we recommend replacing the right and left side tie rods at the same time. We also recommend replacing the bellows, part # pcg419831c sold individually. 2 necessary per car.
From $303.00
Make a selection 99360611400 This temperature sensor is located on the intercooler intake pipe at the back of the intercooler. It monitors the air temperature / density, which affects the fuel mixture. Be sure to replace it when necessary as it can cause an increase in emissions or fuel consumption. Sold individually. 1 necessary per car. View/Change Diagram
From $24.44
Make a selection 99635195930 A must for replacing your brake pads. This kit includes hardware to replace your old clips, backing plates (springs) and cotter pins. For two calipers. View/Change Diagram
From $38.80
Make a selection BAT004 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,029.00
Make a selection BES91105000S This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,014.10
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection BES99101260S - + 20 crank hp & + 14 crank torque. - 200 cell hjs tri-metallic "hd" cats. - 2 tubing (50 mm) with motorsport merge collector. - weighs 18.5 lbs. (8.4 kg). - 1.5 lb (9.1 kg) saving's over OEM header. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - works with OEM sealing rings and clamps. See below for part numbers. - made in Germany. - reduces thermal load and backpressure to for more torque in the mid-range and hp on the top end. Be sure to add new clamps and sealing rings to your order. 2 qty. Clamps are needed, they are part # 99711133690 and 2 qty. Sealing rings are needed, they are part # 98011156100. Our latest development for the GT3 is aimed at those who are looking fo...(choose a part on the right to read more)
$5,286.60
Make a selection BES99102240SHDO + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$3,985.30
Make a selection BES99110200S The headers on this latest 991 system include a double plated flange. This flange dissipates heat and vibration more efficiently and consequently does not warp like thicker single plate flanges commonly used by others. This small advancement is time consuming to make but is added in order to prevent loss of power over time and will ensure years of trouble free operation even under severe track conditions. General Fitment911 2009-12
From $7,707.70
Make a selection BES99120040S Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)
$585.20
Make a selection BES99300240S For all 993 turbo and GT2 General Fitment911 1994-98
$10,794.30
Make a selection 964347009BXATK This steering rack is a remanufactured part with a core, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. The remanufacturing process includes full inspection and testing for structural integrity. We then disassemble and bead blast to remove corrosion. Internals are micro-finished to OEM specifications. Sealing surfaces are carefully checked and restored prior to installing new premium seals and o-rings. Each unit is then carefully tested for full functional...(choose a part on the right to read more)
$1,633.50
Make a selection BES99300241SK The perfect compromise for you and your loved ones. Rich, deep race car tones with the valves open and soft subtle, completely stock sounds with them closed. Torque is better than our other systems in the low range with the valves closed and horsepower is better with the valves open. Made for mid-range and top end performance with the added beauty of 3.5" (90mm) dual exhaust tips! + 27 crank hp & +25 crank torque (on average). - 2.9 tubing (75 mm) at the widest point. Primaries are 2.5" (64mm). - 200 cell hjs "hf" trimetallic catalytic converters. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 3.5" (90 mm) dual oval, double walled polished tips included. - dual high quality ...(choose a part on the right to read more) General Fitment911 1994-98
From $11,730.62
Make a selection BES99602060S Catalytic by pass “x torque” design made by m&m in Germany. General Fitment911 GT3 2003-05
$1,564.20
Make a selection BES99602260S 200 cell catalytic “x torque” design made by m&m in Germany. General Fitment911 GT3 2003-05911 1998-05
$2,823.70
Make a selection BES99701260S2HD Not for cars with OEM muffler. Only for plain tube (catalytic to center muffler) or bes 997… muffler. These headers and cats are perfect for those who want to run sport cats without a software program. Our latest development for the GT3 is aimed at those who are looking for more torque in the mid range, a rich, deep exhaust growl and most importantly no check engine light with stock software. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability matrix design catalytic converters. They have a sm-matrix (winding of three flat and corrugated foils) and a special connection to the matrix sheath, which equates to extremely high durability for track and street use. The added ...(choose a part on the right to read more) General Fitment911 GT3 2007-11
From $4,183.87
Make a selection BES99709260SHD Brombacher racing exhaust system for 997gt3/rs General Fitment911 GT3 2007-11
From $4,665.10
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |